| TK-7302 | TK-8302 | ||
|---|---|---|---|
| GENERAL | |||
| Frequency Range | Type 1 | 136~174 MHz | 450~520 MHz |
| Type 2 | - | 400~470 MHz | |
| Number of Channels | Zone | 2 | 2 |
| Channel | Max.16 | Max.16 | |
| Channel Spacing | 12.5 kHz / 25 kHz | 12.5 kHz / 25 kHz | |
| Operating Voltage | 13.6 V DC±15 % | 13.6 V DC±15 % | |
| Current Drain | Standby | 0.4 A | 0.4 A |
| Receive | 1.0 A | 1.0 A | |
| Transmit | 8.0 A | 8.0 A | |
| Operating Temperature Range | -22 °F ~ +140 °F (-30 °C ~ +60 °C) | -22 °F ~ +140 °F (-30 °C ~ +60 °C) | |
| Frequency Stability | ?2.5 ppm (-22 °F ~ +140 °F ) | ?2.5 ppm (-22 °F ~ +140 °F ) | |
| Antenna Impedance | 50 Ω | 50 Ω | |
| Dimensions (W x H x D), Projections not included | 160 mm x 43 mm x 137 mm | 160 mm x 43 mm x 137 mm | |
| Weight (net) | 1.18 kg | 1.18 kg | |
| RECEIVER (Measurements made per EIA/TIA-603) | |||
| Sensitivity (12dB SINAD) | Wide | 0.28 µV | 0.28 µV |
| Narrow | 0.35 µV | 0.35 µV | |
| Selectivity | Wide | 75 dB | 75 dB |
| Narrow | 65 dB | 65 dB | |
| Intermodulation Distortion | Wide | 70 dB | 70 dB |
| Narrow | 60 dB | 60 dB | |
| Spurious Response | 75 dB | 75 dB | |
| Audio Output (4 Ω impedance) | 4 W with less than 5 % distortion | 4 W with less than 5 % distortion | |
| TRANSMITTER (Measurements made per EIA/TIA-603) | |||
| RF Output Power | 5 W ~ 25 W | 5 W ~ 25 W | |
| Spurious Response | 70 dB | 70 dB | |
| Type of Emission | Wide | 16K0F3E | 16K0F3E |
| Narrow | 11K0F3E | 11K0F3E | |
| FM Hum & Noise | Wide | 45 dB | 45 dB |
| Narrow | 40 dB | 40 dB | |
| Microphone Impedance | 600 Ω | 600 Ω | |
| Audio Distortion | Wide | 3 % | 3 % |
| Narrow | 5 % | 5 % | |
KENWOOD reserves the right to change specifications and features without prior notice.
FleetSync® is a trademark of KENWOOD Corporation.
Windows® is a registered trademark of Microsoft Corporation in the United States and other countries.
| Standard | MIL 810C Methods/Procedures |
MIL 810D Methods/Procedures |
MIL 810E Methods/Procedures |
MIL 810F Methods/Procedures |
|---|---|---|---|---|
| Low Pressure | 500.1 / Procedure I | 500.2 / Procedure I, II | 500.3 / Procedure I, II | 500.4 / Procedure I, II |
| High Temperature | 501.1 / Procedure I, II | 501.2 / Procedure I, II | 501.3 / Procedure I, II | 501.4 / Procedure I, II |
| Low Temperature | 502.1 / Procedure I | 502.2 / Procedure I, II | 502.3 / Procedure I, II | 502.4 / Procedure I, II |
| Temperature Shock | 503.1 / Procedure I | 503.2 / Procedure I | 503.3 / Procedure I | 503.4 / Procedure I, II |
| Solar Radiation | 505.1 / Procedure I | 505.2 / Procedure I | 505.3 / Procedure I | 505.4 / Procedure I |
| Rain*2 | 506.1 / Procedure I, II | 506.2 / Procedure I, II | 506.3 / Procedure I, II | 506.4 / Procedure I, III |
| Humidity | 507.1 / Procedure I, II | 507.2 / Procedure II, III | 507.3 / Procedure II, III | 507.4 |
| Salt Fog*2 | 509.1 / Procedure I | 509.2 / Procedure I | 509.3 / Procedure I | 509.4 |
| Dust*2 | 510.1 / Procedure I | 510.2 / Procedure I | 510.3 / Procedure I | 510.4 / Procedure I, III |
| Vibration | 514.2 / Procedure VIII, X | 514.3 / Procedure I | 514.4 / Procedure I | 514.5 / Procedure I |
| Shock | 516.2 / Procedure I, II, III, V | 516.3 / Procedure I, IV, V | 516.4 / Procedure I, IV, V | 516.5 / Procedure I, IV, V |
| International Protection Standard | ||||
| Dust & Water Protection | IP54*2 | |||
*2: Necessary conditions are: (1) KMC-35/36 microphone is connected; (2) cap is installed on speaker connector; (3) cover is installed on D-sub 15-pin connector; and (4) neither KCT cable nor SP cable is connected.
