TK-D240 | TK-D340 | ||
---|---|---|---|
GENERAL | |||
Frequency Range | 136-174 MHz | 400-470 MHz 450-520 MHz |
|
Number of Channels | 32 ch / 2 zones (Max. 16 ch/ zone) | ||
Channel Spacing | Analog | 25/12.5 kHz | |
Digital | 12.5 kHz | ||
Operating Voltage | 7.5 V DC ± 20 % | ||
Battery Life (5-5-90, battery saver off) |
Analog/Digital | approx. 11.5/13.5 hrs w/KNB-45L approx. 8/10 hrs w/KNB-29N |
|
Operating Temperature Range | -30 ºC to +60 ºC (with KNB-45L: -10 ºC to +60 ºC) |
||
Frequency Stability | ±2.0 ppm | ±1.0 ppm | |
Antenna Impedance | 50 Ω | ||
Dimensions(W x H x D) | w/KNB-45L or KNB-29N |
54 x 121.4 x 33.8 mm | |
Weight | w/KNB-45L | 285 g | |
w/KNB-29N | 370 g | ||
RECEIVER | |||
Sensitivity | Digital 1 % BER | 0.45 μV | |
Digital 5 % BER | 0.3 μV | ||
Analog (12 dB SINAD) | 0.25 μV | ||
Adjacent Channel Selectivity | Analog @ 25/12.5 kHz | 74/68 dB | |
Intermodulation Distortion | Analog | 72 dB | |
Spurious Response | Analog | 70 dB | |
Audio Distortion | Less than 10 % | ||
Audio Output | 1 W/12 Ω (Internal speaker) 500 mW/8 Ω (External speaker) |
||
TRANSMITTER | |||
RF Power Output | 5/1 W | 4/1 W | |
Spurious Response | 70 dB | ||
FM Hum & Noise | Analog @ 25/12.5 kHz | 45/40 dB | |
Audio Distortion | Less than 2 % | ||
Emission Designator | 16K0F3E, 14K0F2D, 14K0F3E, 12K0F2D, 11K0F3E, 7K50F2D, 7K60FXE, 7K60FXD |
Specifications shown are typical.
Analog 25 kHz is not included in the models sold in the USA or US territories.
Analog measurements accord with TIA 603. Digital measurements accord with EN 300 113.
Details and timing of firmware and software updates are subject to change without notice.
Specifications are subject change without notice, due to advancements in technology.
FleetSync® is a registered trademark of JVCKENWOOD Corporation.
AMBE+2™ is a trademark of Digital Voice Systems Inc.
All other trademarks are the property of their respective holders.
Standard | MIL 810C Methods/ Procedures |
MIL 810D Methods/ Procedures |
MIL 810E Methods/ Procedures |
MIL 810F Methods/ Procedures |
MIL 810G Methods/ Procedures |
---|---|---|---|---|---|
Low Pressure | 500.1/Procedure I | 500.2/Procedure I, II | 500.3/Procedure I, II | 500.4/Procedure I, II | 500.5/Procedure I, II |
High Temperature | 501.1/Procedure I, II | 501.2/Procedure I, II | 501.3/Procedure I, II | 501.4/Procedure I, II | 501.5/Procedure I, II |
Low Temperature | 502.1/Procedure I | 502.2/Procedure I, II | 502.3/Procedure I, II | 502.4/Procedure I, II | 502.5/Procedure I, II |
Temperature Shock | 503.1/Procedure I | 503.2/Procedure I | 503.3/Procedure I | 503.4/Procedure I, II | 503.5/Procedure I |
Solar Radiation | 505.1/Procedure I | 505.2/Procedure I | 505.3/Procedure I | 505.4/Procedure I | 505.5/Procedure I |
Rain | 506.1/Procedure I, II | 506.2/Procedure I, II | 506.3/Procedure I, II | 506.4/Procedure I, III | 506.5/Procedure I, III |
Humidity | 507.1/Procedure I, II | 507.2/Procedure II, III | 507.3/Procedure II, III | 507.4 | 507.5/Procedure II |
Salt Fog | 509.1/Procedure I | 509.2/Procedure I | 509.3/Procedure I | 509.4 | 509.5 |
Dust | 510.1/Procedure I | 510.2/Procedure I | 510.3/Procedure I | 510.4/Procedure I, III | 510.5/Procedure I |
Vibration | 514.2/Procedure VIII, X | 514.3/Procedure I | 514.4/Procedure I | 514.5/Procedure I | 514.6/Procedure I |
Shock | 516.2/Procedure I, II, V | 516.3/Procedure I, IV | 516.4/Procedure I, IV | 516.5/Procedure I, IV | 516.6/Procedure I, IV |
International Protection Standard | |||||
Dust & Water Protection | IP54/IP55 |
*1: The 2-pin connector cover has to be connected to the radio, or the locking bracket has to be attached to the KMC-45D external speaker microphone.