| GENERAL | |||
|---|---|---|---|
| NX-240 | NX-340 | ||
| Frequency Range | 136-174 MHz | 400-470 MHz 450-520 MHz |
|
| Number of Channels | 32 | ||
| Zones | 2 | ||
| Max. Channels per Zone | 16 | ||
| Channel Spacing | Analog Digital |
25* / 12.5 kHz 12.5* / 6.25 kHz |
|
| Operating Voltage | 7.5V DC ± 20% | ||
| Battery Life 5-5-90 during hi-power battery saver: |
OFF/ON with KNB-45L (2000mAh) | Approx. 10/12 hours | |
| Operating Temperature Range | -30°C ~ +60°C | ||
| Frequency Stability | ±2.0ppm | ±1.0ppm | |
| Antenna Impedance | 50 Ω | ||
| Dimensions (W x H x D) | With KNB-45L, Projections Not Included |
54 x 122 x 35.3 mm | |
| Weight (net) | Radio only With KNB-45L |
165 g 281 g |
|
| RECEIVER | ||
|---|---|---|
| Sensitivity | Digital Analog (12 dB SINAD) |
0.25 μV 0.25 μV |
| Selectivity | Analog 25 / 12.5KHz |
70 dB / 60 dB |
| Intermodulation Distortion | Analog | 60 dB |
| Spurious Response | Analog | 70 dB |
| Audio Distortion | Less than 10% | |
| Audio Output | 1 W / 12 Ω (Internal Speaker) 500mW / 8 Ω (External Output) | |
| TRANSMITTER | ||
| RF Power Output | High / Low | 5 W / 1 W |
| Spurious Response | 70 dB | |
| FM Hum & Noise | Analog 25 / 12.5KHz |
45 dB / 40 dB |
| Audio Distortion | Less than 10% | |
| Modulation | 16K0F3E, 11K0F3E, 4K00F1E, 4K00F1D, 4K00F7W, 4K00F2D, 8K30F1E, 8K30F1D, 8K30F7W |
|
Specifications are subject to change without notice, due to advancements in technology.
Measurements made per TIA/EIA-603 and Specification are typical.
FleetSync® is a registered trademark of JVCKENWOOD Corporation.
Windows® is a registered trademark of Microsoft Corporation in the United States and other countries.
AMBE+2™ is a trademark of Digital Voice Systems Inc.
NXDN® is a registered trademark of JVCKENWOOD Corporation and Icom Inc.
NEXEDGE® is a registered trademark of JVCKENWOOD Corporation.
*Version 2.0 models are compatible with Analog 25KHz & Digital 12.5kHz
| MIL Standard | MIL 810C Methods/ Procedures |
MIL 810D Methods/ Procedures |
MIL 810E Methods/ Procedures |
MIL 810F Methods/ Procedures |
MIL 810G Methods/ Procedures |
|---|---|---|---|---|---|
| Low Pressure | 500.1/ Procedure I |
500.2/ Procedure I, II |
500.3/ Procedure I, II |
500.4/ Procedure I, II |
500.5/ Procedure I, II |
| High Temperature | 501.1/ Procedure I, I |
501.2/ Procedure I, II |
501.3/ Procedure I, II |
501.4/ Procedure I, II |
501.5/ Procedure I, II |
| Low Temperature | 502.1/ Procedure I |
502.2/ Procedure I, II |
502.3/ Procedure I, II |
502.4/ Procedure I, II |
502.5/ Procedure I, II |
| Temperature Shock | 503.1/ Procedure I |
503.2/ Procedure I |
503.3/ Procedure I |
503.4/ Procedure I, II |
503.5/ Procedure I |
| Solar Radiation | 505.1/ Procedure I |
505.2/ Procedure I |
505.3/ Procedure I |
505.4/ Procedure I |
505.5/ Procedure I |
| Rain | 506.1/ Procedure I, II |
506.2/ Procedure I, II |
506.3/ Procedure I, II |
506.4/ Procedure I, III |
506.5/ Procedure I, III |
| Humidity | 507.1/ Procedure I, II |
507.2/ Procedure II, II |
507.3/ Procedure II, III |
507.4 | 507.5/ Procedure II |
| Salt Fog | 509.1/ Procedure I |
509.2/ Procedure I |
509.3/ Procedure I |
509.4 | 509.5 |
| Dust | 510.1/ Procedure I |
510.2/ Procedure I |
510.3/ Procedure I |
510.4/ Procedure I, III |
510.5/ Procedure I |
| Vibration | 514.2/ Procedure VIII, X |
514.3/ Procedure I |
514.4/ Procedure I |
514.5/ Procedure I |
514.6/ Procedure I |
| Shock | 516.2/ Procedure I, II, V |
516.3/ Procedure I, IV |
516.4/ Procedure I, IV |
516.5/ Procedure I, IV |
516.6/ Procedure I, IV |
| International Protection Standard | |||||
| Dust & Water Protection | IP54/55 | ||||
To meet MIL-810 and IP grade, the 2-pin connector has to be connected.
