TM-D750A/E
Firmware update information
Last updated : October 28, 2026

The TM-D750A/E firmware has been updated from Version 1.02 to Version 1.03 as follows.
TM-D750A/E owners can update the transceiver’s firmware by using a microSD memory card as detailed below.
 
Updated items : (Version 1.02 1.03) [October 28, 2026]  
The following symptoms are revised.
1. The built-in KISS TNC may stop functioning properly during use.
2. Host files may not be obtained correctly in D-STAR Direct Mode.
3. When VOX is ON, stored DTMF sequences may not be transmitted correctly during transmission.
4. When the PTT band and the operating band are different, the 1750 Hz tone may not be transmitted correctly.
5. The deviation of signals transmitted during cross-band repeater operation is low (TM-D750A only).
 
Applicable units :
The firmware update is applicable to the following units.
Model: TM-D750A, TM-D750E
Serial numbers: From S/NO.C62XXXXX through S/NO.C69XXXXX approx.
Notes : You can find the serial number imprinted on the TM-D750A/E's Main Unit bottom side; it consists of an 8-digit number beginning with "S/NO."
: You can check the firmware version of your TM-D750A/E by accessing Menu No.992. The firmware version appears in the LCD display.
Firmware updating procedure using a USB cable

Follow this procedure if you connect your PC to the transceiver using a USB cable.
You can copy the firmware file while the microSD memory card remains inserted in the transceiver.


1) Download the firmware file "TM-D750_V103.zip" to your PC.
2) Turn OFF the transceiver and insert a microSD memory card into the microSD memory card slot on the right side of the operation panel.
3) Turn ON the transceiver.
When the microSD memory card is recognized, the [SD] icon appears at the top of the display, and the required folders are created on the microSD memory card.
4) Set Menu No. 980 (USB Function) to "Mass Storage".
5) Connect the USB connector on the left side of the operation panel to your PC using a USB cable.
"Mass Storage Mode" appears on the operation panel display.
6) In File Explorer on your PC, open the microSD memory card, which is recognized as a USB drive, and copy the firmware file "TM-D750_V103.zip" to the following folder on the card:
[KENWOOD] > [TM-D750] > [FIRMWARE]
Copy the ZIP file as is, without renaming or extracting it.
7) After copying is complete, turn OFF the transceiver and disconnect the USB cable from the operation panel.
8) Press and hold the [MENU] key (the bottom key among the four keys on the left side of the display) and the Power switch simultaneously for at least 10 seconds, without releasing either one, until the startup beep sounds.
* If you release either one before the startup beep sounds, the transceiver will not enter Firmware Programming Mode.
9) When the startup beep sounds and the "Firmware Programming Mode" screen appears, release both.
The current firmware version is displayed.
10) Press [SD].
11) Select "TM-D750_V103.zip" and press [ENC] (the encoder).
12) When "You wish to update the firmware?" appears, press [YES].
The firmware update starts, and [PROGRAM] blinks.
The update takes approximately 22 minutes.
Do not turn OFF the transceiver during the update.
When the update is complete, "Completed!!" appears.
13) Press [OK].
The transceiver restarts with the new firmware.
Firmware updating procedure without a USB Cable

Follow this procedure if you do not connect your PC to the transceiver using a USB cable.
Use your PC's card slot or a card reader to copy the firmware file.


1) Download the firmware file "TM-D750_V103.zip" to your PC.
2) Turn OFF the transceiver and insert a microSD memory card into the microSD memory card slot on the right side of the operation panel.
3) Turn ON the transceiver.
When the microSD memory card is recognized, the [SD] icon appears at the top of the display, and the required folders are created on the microSD memory card.
4) Turn OFF the transceiver and remove the microSD memory card.
5) Insert the removed microSD memory card into your PC's card slot or a card reader.
Copy the firmware file "TM-D750_V103.zip" to the following folder on the card:
[KENWOOD] > [TM-D750] > [FIRMWARE]
Copy the ZIP file as is, without renaming or extracting it.
6) After copying is complete, remove the microSD memory card from your PC's card slot or the card reader and insert it into the microSD memory card slot on the right side of the operation panel.
7) Press and hold the [MENU] key (the bottom key among the four keys on the left side of the display) and the Power switch simultaneously for at least 10 seconds, without releasing either one, until the startup beep sounds.
* If you release either one before the startup beep sounds, the transceiver will not enter Firmware Programming Mode.
8) When the startup beep sounds and the "Firmware Programming Mode" screen appears, release both.
The current firmware version is displayed.
9) Press [SD].
10) Select "TM-D750_V103.zip" and press [ENC] (the encoder).
11) When "You wish to update the firmware?" appears, press [YES].
The firmware update starts, and [PROGRAM] blinks.
The update takes approximately 22 minutes.
Do not turn OFF the transceiver during the update.
When the update is complete, "Completed!!" appears.
12) Press [OK].
The transceiver restarts with the new firmware.
Downloading
Only if you agree to the following "Usage Notes", click "Agree" and download the file.
(If you do not agree, you will not be able to download the file.)
Usage Notes
・ JVCKENWOOD Corporation does not warrant that quality and functions of this software comply with each user's purpose of use of this software, and unless specifically described in this document, JVCKENWOOD Corporation shall be free from any responsibilities to any defects and indemnities to any damages or losses. Selection and installation of this software shall be done by the user's own designation. The user shall take full responsibility for the use and effects of this software.
・ JVCKENWOOD Corporation shall be free from any responsibilities for any incidental losses or damages, such as missing communications or a call opportunity, caused by a failure or performance error of this software.
・ This software consists of a multiple number of and individual software components. Title to and ownership of copyrights for each software component is reserved for JVCKENWOOD Corporation and the respective bona fide holder. Any copying, reproducing or disclosing on an Internet website of the JVCKENWOOD Corporation copyrighted software components is strictly prohibited. Furthermore, any reselling, assigning or transferring of the JVCKENWOOD Corporation copyrighted software components is also strictly prohibited without embedding the software in the product memories.
・ The software employs the software component in accordance with the End User License Agreement (hereinafter referred to as the "EULA") stipulated by JVCKENWOOD Corporation and/or the respective bona fide holder.
Some of the software components licensed under the "EULA" are free software, and a distribution condition of the software component in the executable format under the terms and conditions contained in the GNU General Public License or GNU Lesser General Public License (hereinafter referred to as the "GPL/LGPL") requires that the source code for the relevant software components be made available.
Access the URL below for details of the software component stipulated in the "GPL/LGPL".
https://www.kenwood.com/gpl/e.html
Please note that we are unable to answer any inquiry relating to the contents, etc. of the source code.
Please note that software components licensed under "EULA" and those developed or created independently by JVCKENWOOD Corporation shall not be subject to the requirement for provision of the source code if they are not subject to "GPL/LGPL".
・ For license information regarding the open-source software included in this software, please refer to the "Open Source Software License Information" posted on our website at the address below.
https://manuals.jvckenwood.com/en/
・ The Software License Agreement can be viewed in Menu No. 993, "EULA," on the transceiver.
・ Important notices regarding the software can be viewed in Menu No. 994, "Important Notices," on the transceiver.

Agree

TM-D750_V103.zip : 464MB download TM-D750_V103.zip : 464MB download

TM-D750A/E Firmware Version 1.03 (October / 2026)