TM-D710GA / TM-D710GE
Main firmware update information
Last updated : November 25, 2020
The TM-D710GA/GE transceiver's main firmware has been updated from Version 1.01 to Version 1.02 as follows.
We are offering the firmware updating program to the TM-D710GA/GE owners.
You can update the firmware by connecting the TM-D710GA/GE to the PC by using an optional Programming Cable (PG-5G, or PG-5H Serial communications cable).
The firmware updating program is not applicable for the TM-V71A/E or TM-D710A/E.
Updated item : (Ver.1.01 1.02) [November 25, 2020]
  The following symptom is revised.
  1. When using the new accessory microphone (MC-62), microphone key presses may be falsely detected under certain conditions.

Updated item : (Ver.1.00 1.01) [August 26, 2020]
  The following symptom is revised.
  1. The Memory Scan may not work correctly under certain conditions.
Applicable models/units :
The firmware updating program is applicable for following models/units.
Models: TM-D710GA /TM-D710GE
Serial numbers: From S/NO.B3Axxxxx through S/NO.C0Bxxxxx approx.
Notes : You can find the serial number imprinted on the main body bottom cover; it consists of an 8-digit number beginning with "S/NO."
: You can check the firmware version of your TM-D710GA/GE by the following procedures.
1. With using the MCP-6A
  Select "Model" and then "Product Information" in the MCP-6A menu after connecting the transceiver with a PC by using the PG-5G or PG-5H PC interface cable.
2. Without using the MCP-6A (TM-D710GA/GE standalone)
  Press [PF1] + Power ON.
The firmware version appears in the left side of the LCD display.
: The firmware updating program cannot be used for the Japanese models TM-D710G/GS.

Operating Environments
1. Operating System (OS)
  Windows® 8.1 (32-bit or 64-bit),
Windows® 10 (32-bit or 64-bit)
This software is designed to run on the above operating systems.
This software also runs on Windows® 11. (Noted on June 23, 2022)
Applicable operating systems are subject to change without notice due to the end of the technical support by Microsoft Corporation or change of the product specifications.
2. Processor
  Faster than the recommended CPU for each OS.
3. System Memory (RAM)
  Larger than the recommended System Memory for each OS.
4. Free Hard Drive Space
  Larger than the recommended Free Hard Drive Space for each OS.
5. Runtime
Microsoft .NET Framework 3.5 (includes .NET 2.0 and 3.0).
6. Peripheral Devices
A display with resolutions higher than VGA.(640 x 480)
A keyboard and a mouse, or other pointing devices.
An RS-232C interface.
An optional programming cable.(PG-5G, or PG-5H Serial communications cable)
If you do not want to lose user data, save the data using the Memory Control Program MCP-6A before updating the firmware and write the data back after updating the firmware.
Usage Notes
Users are prohibited to assign, rent, lease, redistribute, or resell the software.
Users are prohibited to revise, change, translate, merge, de-compile, or reverse engineer the software.
The quality and performance of the software is not warranted for the applicability of any users. JVCKENWOOD Corporation shall not assume liability for any defects, nor warrant anything other than is expressly provided in the agreement. The selection and introduction of the products as well as the results there from shall be upon the liability of the users.
JVCKENWOOD Corporation shall own all copyrights and other intellectual properties for the software and all manuals and documents attached to the software. The user shall be allowed to use, not to resell, the software by obtaining a license from JVCKENWOOD Corporation. While the media in which the software is stored is possessed by the user, the ownership for the software itself shall be reserved for JVCKENWOOD Corporation.
Installation :
1. Extract the downloaded file "" into a designated folder.
In the designated folder, a folder labeled "TM-D710G_Main_V102E" will be created.
2. In the folder labeled "TM-D710G_Main_V102E", the firmware updating program "TM-D710G_Main_V102_e.exe" and "TM-D710G_Main_e.chm" are automatically created.
Click to read the firmware updating procedure.
Uninstalling :
Delete the folder labeled "TM-D710G_Main_V102E" manually using the Explorer or an alternative method.
If you agree with the details listed above, click the following link to download the firmware updating program.
(The latest version includes all previous updates.)
Latest update: TM-D710G Main Firmware Update Version 1.02 (November / 2020) : 1.17MB download
Windows is a registered trademark or trademark of Microsoft Corporation in the United States and other countries.
.NET Framework is a registered trademark or trademark of Microsoft Corporation in the United States and other countries.