TH-D7A / TH-D7E / TH-D7E(Ver.2.0)
Memory Control Program
MCP-D7 Version 1.20
 
 
Notes :
This program is for editing "Memory Channels", "APRS"(*1), "SKY COMMAND II"(*2) and various settings on the KENWOOD amateur radio TH-D7A/D7E/D7E(Ver.2.0).
This program does not work with the TH-D7A(G) / TH-D7A(G2.0) / TH-D7E(G2.0).
For the TH-D7A(G)/D7A(G2.0)/D7E(G2.0) uses, we are offering the MCP-D7G Memory Control Program.
This program runs on Windows 95/98/Me/2000.(*3)
(This program might not operate on Windows NT4.0/XP)
To write to or read from the TH-D7 memory, a separate connector cable PG-4W(option) is required.
About 1MB of free hard disk space is needed to install this program.
At least 5MB of memory is required to run this program.
Before connecting the TH-D7 to a PC, first turn the TH-D7 power OFF.
Permission is required if this program is to be redistributed on a personal web site.
Any user may not be engaged in the following acts:
To revise, change, edit, merge, de-compile or reverse engineer the Software.
The quality and performance of the Products shall not warrant the applicability to the purpose of any user. KENWOOD shall not assume any liability for defects, or warrant anything other than expressly provided in the document. The selection and introduction of the Products as well as the results therefrom shall be upon the liability of the users.
KENWOOD shall own all copyrights and other intellectual properties for the Products and all manuals and documents attached to the Products.
User shall be hereby allowed to use, not sell, the Software packed in the Products by KENWOOD. While the disc in which the Software is stored is possessed by the user, the ownership for the Software itself shall be reserved for KENWOOD.
(*1) The Automatic Packet/Position Reporting System(APRS) is a registered trademark of Bob Bruninga,WB4APR in the United States.
(*2) The SKY COMMAND II is a trademark of KENWOOD Corporation in the United States or other countries.
(*3) Windows are either registered trademarks or trademarks of Microsoft Corporation.
 
Installation :
1. Execute the downloaded self-extracting file "MD7120.exe" and extract the installation program into a designated folder.
2. In the designated folder, a folder labeled "Mcp-d7" will be created.
Execute the Setup.exe file in the "disk1" folder in the "Mcp-d7" folder to begin installation.
3. When the instruction for selecting country version appears, select version in use. If you specify the wrong version, the program will not function properly.
4. If you have specified wrong version, repeat the installation procedure form the beginning.
 
Uninstallation :
1. Delete MCP-D7 by executing [Control Panel]-[Add/Remove Programs].
2. The files created by MCP-D7 are not delete. Delete those files manually.
3. When files have been linked, delete the [D7 File] by [File Types] in the [View]-[Options] menu in the Windows Explorer.
 
Caution :
Windows 2000 compatibility
When you read or write a file to the transceiver's memory contents using a notebook PC (Windows 2000), you may get the error message: "Communication timeout error".
In this case, confirm the connection between the transceiver and PC.
  If the problem persists:
1. Select the Pause option (Radio -> Pause).
2. When you select this option, you will be prompted to turn the transceiver OFF and then ON.
3. After you turn the transceiver ON again, press [OK].
Communication between the transceiver and PC begins.
  This problem is likely to happen with the TH-D7A/D7E/D7E(Ver2.0) transceivers.
 
History :
Ver 1.10
- We supported COM3 and COM4.
Ver 1.11
- After performing the sort function and saving the file to a PC, the memory channels were not in alphabetical order. FIXED.
- After reading a data file, the program could no longer read a VFO frequency on the UHF band. FIXED.
- After reading a data file, the "Position Limit"/ "Distance" parameter in the APRS menu would become 10. FIXED.
- After reading a data file, the program would not display icons with overlaid text in the APRS menu. FIXED.
- Added a packet speed selection menu for TH-D7E Ver.2.0 (only).
Ver 1.20
- We supported Windows Me/2000.
TH-D7A/D7E/D7E(Ver.2.0) Memory Control Program
Latest update: MCP-D7 Version 1.20 (Jan./2002)
MD7120.exe 1.03MB download