Support

TK-5410

Model TK-5410
GENERAL
Models 4-key w/LCD Model TK-5410K2
Full key w/LCD Model TK-5410K3
Frequency Range Receive 763-776, 851-870 MHz
Transmit 763-776, 793-806, 806-825, 851-870 MHz
Number of Channels 1024
Zones 100
Max. Channels per Zone 512
Channel Spacing Analog 12.5 / 25 KHz
Digital 12.5 kHz
PLL Channel Steps 12.5 kHz
Operating Voltage 7.5 VDC ± 20 %
Battery Life 5-5-90 (10-10-80) duty cycle KNB-54N, 7.5 VDC, 2500 mAh 12 hours (8 hours)
KNB-41NC, 7.5V DC, 2500mAh 12 hours (8 hours)
KBP-6, AA Alkaline x6 Batteries (@ 1W) 8 hours (5 hours)
Operating Temperature Range -22° F to +140° F (-30° C to +60° C)
Frequency Stability ± 1.5 ppm (-22° F to +140° F)
Antenna Impedance 50 Ω
Dimensions (W x H x D) (projections not included) with KNB-54N 2.28 x 6.10 x 1.80 in. (58 x 155 x 45.7 mm.)
with KNB-41NC 2.28 x 6.10 x 1.84 in. (58 x 155 x 46.7 mm.)
with KBP-6 2.36 x 6.10 x 1.84 in. (60 x 155 x 46.7 mm.)
Weight (Radio only) 4-key w/LCD Model 11.64 oz. (330 g)
Full key w/LCD Model 11.64 oz. (330 g)
Weight w/Antenna & Belt Clip (4-Key w/LCD Model) with KNB-54N 23.28 oz. (660 g)
with KNB-41NC 24.00 oz. (680 g)
FCC ID ALH420700
IC Certification 282D-420700
RECEIVER
Sensitivity Digital (5 % BER) 0.25 μV
Digital (1 % BER) 0.40 μV
Analog 12 dB SINAD 0.25 μV
Selectivity Digital -60 dB
Analog @ 25 kHz -75 dB
Analog @ 12.5 kHz -64 dB
Intermodulation Distortion -75 dB
Spurious & Image -75 dB
Audio Distortion Digital Less than 1.0 %
Analog Less than 2.0 %
Audio Output 500 mW / 8 Ω
TRANSMITTER
RF Power Output 3 W / 1 W
Spurious & Harmonics 70 dB
FM Hum & Noise Analog @ 25 kHz 45 dB
Analog @ 12.5 kHz 40 dB
Audio Distortion Less than 2 %
Modulation Limiting Analog @ 25 KHz ± 5 kHz
Analog @ NPSPAC ± 4 kHz
Analog @ 12.5 KHz ± 2.5 kHz
Modulation 16K0F3E, 11K0F3E, 8K10F1E, 8K10F1D, 14K0F3E

Analog measurements made per TIA/EIA 603 and specifications shown are typical. Digital measurements made per TIA/EIA 102CAAA and specifications shown are typical.

Kenwood follows a policy of continuous advancement in development. For this reason specifications may be changed without notice.