Support

TK-2360/3360

  TK-2360 TK-3260
GENERAL
Frequency Range
Type 1
Type 2
 
136 ~ 174 MHz
-
 
-
400 ~ 470 MHz
Number of Channels Max.16
Channel spacing
Wide / Narrow
 
25, 30 kHz / 12.5, 15 kHz
 
25 kHz / 12.5 kHz
Battery Voltage 7.5 V DC ± 20%
Battery Life (5-5-90 duty cycle, save off)
with KNB-55L (1480 mAh)
with KNB-56N (1400 mAh)
with KNB-57L (2000 mAh)
 
Approx. 9 hours
Approx. 9 hours
Approx. 13 hours
Operating Temperature Range -30°C to +60°C
(-10°C ~ +60°C when KNB-55L / 57L in use)
Frequency Stability ±2.5 ppm (-30°C ~ +60°C)
Antenna impedance 50 Ω
Channel Frequency Spread 38 MHz 70 MHz
Dimensions (W x H x D),
Projections not included
Radio Only
with KNB-55L
with KNB-56N
with KNB-57L
 
 
56.0 x 103.7 x 14.0 mm
56.0 x 103.7 x 29.1 mm
56.0 x 103.7 x 33.8 mm
56.0 x 103.7 x 30.1 mm
Weight (net)
Radio Only
with KNB-55L
with KNB-56N
with KNB-57L
 
163 g
270 g
380 g
305 g
FCC ID
Type 1
Type 2
 
ALH415000
-
 
-
ALH415101
RECEIVER
Sensitivity (12 dB SINAD)
Wide / Narrow
 
0.25 µV / 0.28 µV
Selectivity
Wide / Narrow
 
70 dB / 63 dB
Intermodulation Distortion
Wide / Narrow
 
68 dB / 68 dB
Spurious Response 70 dB
Spurious Response Rejection (Analogue) 75 dB
Audio Distortion Less than 5%
Audio Output 500 mW / 8 Ω
TRANSMITTER
RF Power Output
High / Low
 
5 W / 1 W
Spurious Response 70 dB
Type of Emission
Wide / Narrow
 
16K0F3E / 11K0F3E
FM HUM & Noise
Wide / Narrow
 
45 dB / 43 dB
Modulation Distortion Less than 5 %

Measurements made per TIA/EIA 603 and specifications shown are typical.
KENWOOD follows a policy of countinuous advancement in development.
For this reason specifications may be changed without notice.
FleetSync® is a registered trademark of KENWOOD Corporation.

Applicable MIL-STD & IP

Standard MIL 810C
Methods/Procedures
MIL 810D
Methods/Procedures
MIL 810E
Methods/Procedures
MIL 810F
Methods/Procedures
Low Pressure 500.1/Procedure I 500.2/Procedure I, II 500.3/Procedure I, II 500.4/Procedure I, II
High Temperature 501.1/Procedure I, II 501.2/Procedure I, II 501.3/Procedure I, II 501.4/Procedure I, II
Low Temperature 502.1/Procedure I 502.2/Procedure I, II 502.3/Procedure I, II 502.4/Procedure I, II
Temperature Shock 503.1/Procedure I 503.2/Procedure I 503.3/Procedure I 503.4/Procedure I, II
Solar Radiation 505.1/Procedure I 505.2/Procedure I 505.3/Procedure I 505.4/Procedure I
Rain 506.1/Procedure I, II 506.2/Procedure I, II 506.3/Procedure I, II 506.4/Procedure I, III
Humidity 507.1/Procedure I, II 507.2/Procedure II, III 507.3/Procedure II, III 507.4
Salt Fog 509.1/Procedure I 509.2/Procedure I 509.3/Procedure I 509.4
Dust 510.1/Procedure I 510.2/Procedure I 510.3/Procedure I 510.4/Procedure I, III
Vibration 514.2/Procedure VIII, X 514.3/Procedure I 514.4/Procedure I 514.5/Procedure I
Shock 516.2/Procedure I, II, V 516.3/Procedure I, IV 516.4/Procedure I, IV 516.5/Procedure I, IV
International Protection Standard
Dust & Water Protection *2 IP54/55

*1 To meet the blowing-rain condition, the 2-pin connector cover has to be connected on the radio.
*2 To meet IP54/55, the 2-pin connector cover has to be connected on the radio;
    the locking bracket has to be attached to the KMC-45 external speaker microphone.