TK-7360/8360

  TK-7360 TK-8360
GENERAL
Frequency Range
Type 1
Type 2
136~174 MHz
450~520 MHz
400~470 MHz
Number of Channels/ Zones 128 / 128 128 / 128
Channel Spacing
Wide / Narrow
25 kHz / 12.5 kHz 25 kHz / 12.5 kHz
Operating Voltage 13.6 V DC±15 % 13.6 V DC±15 %
Current Drain
Standby Receive Transmit (M / H)
0.4 A                    0.4 A
1.0 A                    1.0 A
8.0 A                   14.0 A
0.4 A                    0.4 A
1.0 A                    1.0 A
8.0 A                   14.0 A
Operating Temperature Range -30 ºC ~ +60 ºC -30 ºC ~ +60 ºC
Frequency Stability ±2.5 ppm (-30 ºC ~ +60 ºC ) ±2.5 ppm ( -30 ºC ~ +60 ºC )
Antenna Impedance 50 Ω 50 Ω
Dimensions (W x H x D), Projections not included 160 mm x 43 mm x 136 mm 160 mm x 43 mm x 136 mm
 Weight (net) 2.0 kg 2.0 kg
Sensitivity (12dB SINAD)
Wide Narrow
0.28 µV
0.35 µV
0.28 µV
0.35 µV
Selectivity
Wide Narrow
75 dB
65 dB
75 dB
65 dB
Intermodulation Distortion Wide
Narrow
70 dB
65 dB
70 dB
65 dB
Spurious Response 75 dB 75 dB
Audio Output
(4 Ω impedance)
4 W with less than 5 % distortion 4 W with less than 5 % distortion
TRANSMITTER (Measurements made per EIA/TIA-603)
RF Power Output 5 W ~ 25 W 5 W ~ 50 W 5 W ~ 25 W 5 W ~ 45 W
Spurious Response 70 dB 70 dB
Type of Emission Wide Narrow 16K0F3E
11K0F3E
16K0F3E
11K0F3E
FM Hum & Noise Wide Narrow 45 dB
40 dB
45 dB
40 dB
Microphone Impedance 600 Ω 600 Ω
Audio Distortion Wide Narrow 3 %
5 %
3 %
5 %

KENWOOD reserves the right to change specifications and features without prior notice.
FleetSync® is a registered trademark of KENWOOD Corporation.
Windows® is a registered trademark of Microsoft Corporation in the United States and other countries.

Applicable MIL-STD & IP

Standard MIL 810C
Methods/Procedures
MIL 810D
Methods/Procedures
MIL 810E
Methods/Procedures
MIL 810F
Methods/Procedures
Low Pressure 500.1 / Procedure I 500.2 / Procedure I, II 500.3 / Procedure I, II 500.4 / Procedure I, II
High Temperature 501.1 / Procedure I, II 501.2 / Procedure I, II 501.3 / Procedure I, II 501.4 / Procedure I, II
Low Temperature 502.1 / Procedure I 502.2 / Procedure I, II 502.3 / Procedure I, II 502.4 / Procedure I, II
Temperature Shock 503.1 / Procedure I 503.2 / Procedure I 503.3 / Procedure I 503.4 / Procedure I, II
Solar Radiation 505.1 / Procedure I 505.2 / Procedure I 505.3 / Procedure I 505.4 / Procedure I
Rain*2 506.1 / Procedure I, II 506.2 / Procedure I, II 506.3 / Procedure I, II 506.4 / Procedure I, III
Humidity 507.1 / Procedure I, II 507.2 / Procedure II, III 507.3 / Procedure II, III 507.4
Salt Fog*2 509.1 / Procedure I 509.2 / Procedure I 509.3 / Procedure I 509.4
Dust*2 510.1 / Procedure I 510.2 / Procedure I 510.3 / Procedure I 510.4 / Procedure I, III
Vibration 514.2 / Procedure VIII, X 514.3 / Procedure I 514.4 / Procedure I 514.5 / Procedure I
Shock 516.2 / Procedure I, II, III, V 516.3 / Procedure I, IV, V 516.4 / Procedure I, IV, V 516.5 / Procedure I, IV, V
International Protection Standard
Dust & Water Protection IP54*2

*2: Necessary conditions are: (1) KMC-35/36 microphone is connected; (2) cap is installed on speaker connector; (3) cover is installed on D-sub 15-pin connector; and (4) neither KCT cable nor SP cable is connected.