TK-7302(H)/8302(H)

  TK-7302 TK-8302
GENERAL
Frequency Range Type 1 136~174 MHz 450~520 MHz
Type 2 - 400~470 MHz
Number of Channels Zone 2 2
Channel Max.16 Max.16
Channel Spacing 12.5 kHz / 25 kHz 12.5 kHz / 25 kHz
Operating Voltage 13.6 V DC±15 % 13.6 V DC±15 %
Current Drain Standby 0.4 A 0.4 A
Receive 1.0 A 1.0 A
Transmit 8.0 A 8.0 A
Operating Temperature Range -22 °F ~ +140 °F (-30 °C ~ +60 °C) -22 °F ~ +140 °F (-30 °C ~ +60 °C)
Frequency Stability ?2.5 ppm (-22 °F ~ +140 °F ) ?2.5 ppm (-22 °F ~ +140 °F )
Antenna Impedance 50 Ω 50 Ω
Dimensions (W x H x D), Projections not included 160 mm x 43 mm x 137 mm 160 mm x 43 mm x 137 mm
Weight (net) 1.18 kg 1.18 kg
RECEIVER (Measurements made per EIA/TIA-603)
Sensitivity (12dB SINAD) Wide 0.28 µV 0.28 µV
Narrow 0.35 µV 0.35 µV
Selectivity Wide 75 dB 75 dB
Narrow 65 dB 65 dB
Intermodulation Distortion Wide 70 dB 70 dB
Narrow 60 dB 60 dB
Spurious Response 75 dB 75 dB
Audio Output (4 Ω impedance) 4 W with less than 5 % distortion 4 W with less than 5 % distortion
TRANSMITTER (Measurements made per EIA/TIA-603)
RF Output Power 5 W ~ 25 W 5 W ~ 25 W
Spurious Response 70 dB 70 dB
Type of Emission Wide 16K0F3E 16K0F3E
Narrow 11K0F3E 11K0F3E
FM Hum & Noise Wide 45 dB 45 dB
Narrow 40 dB 40 dB
Microphone Impedance 600 Ω 600 Ω
Audio Distortion Wide 3 % 3 %
Narrow 5 % 5 %

 

KENWOOD reserves the right to change specifications and features without prior notice.
FleetSync® is a trademark of KENWOOD Corporation.
Windows® is a registered trademark of Microsoft Corporation in the United States and other countries.

Applicable MIL-STD & IP

Standard MIL 810C
Methods/Procedures
MIL 810D
Methods/Procedures
MIL 810E
Methods/Procedures
MIL 810F
Methods/Procedures
Low Pressure 500.1 / Procedure I 500.2 / Procedure I, II 500.3 / Procedure I, II 500.4 / Procedure I, II
High Temperature 501.1 / Procedure I, II 501.2 / Procedure I, II 501.3 / Procedure I, II 501.4 / Procedure I, II
Low Temperature 502.1 / Procedure I 502.2 / Procedure I, II 502.3 / Procedure I, II 502.4 / Procedure I, II
Temperature Shock 503.1 / Procedure I 503.2 / Procedure I 503.3 / Procedure I 503.4 / Procedure I, II
Solar Radiation 505.1 / Procedure I 505.2 / Procedure I 505.3 / Procedure I 505.4 / Procedure I
Rain*2 506.1 / Procedure I, II 506.2 / Procedure I, II 506.3 / Procedure I, II 506.4 / Procedure I, III
Humidity 507.1 / Procedure I, II 507.2 / Procedure II, III 507.3 / Procedure II, III 507.4
Salt Fog*2 509.1 / Procedure I 509.2 / Procedure I 509.3 / Procedure I 509.4
Dust*2 510.1 / Procedure I 510.2 / Procedure I 510.3 / Procedure I 510.4 / Procedure I, III
Vibration 514.2 / Procedure VIII, X 514.3 / Procedure I 514.4 / Procedure I 514.5 / Procedure I
Shock 516.2 / Procedure I, II, III, V 516.3 / Procedure I, IV, V 516.4 / Procedure I, IV, V 516.5 / Procedure I, IV, V
International Protection Standard
Dust & Water Protection IP54*2

*2: Necessary conditions are: (1) KMC-35/36 microphone is connected; (2) cap is installed on speaker connector; (3) cover is installed on D-sub 15-pin connector; and (4) neither KCT cable nor SP cable is connected.