KENWOOD
Global Site
KENWOOD USB Audio Controller
ARUA-10 Version 3.00
Last updated : October 31, 2014
About this software
This is the software to be used to connect a TS-990S, a TS-590SG, or a TS-590S transceiver and a PC by a USB cable and make it possible to use a speaker and a microphone on your PC instead of those on the transceiver.
Using this software coupled with ARCP-990, ARCP-590G, or ARCP-590, simply connecting a PC to a transceiver using a USB cable makes it possible to control the transceiver from the PC.

Note:
A virtual COM port driver needs to be installed onto the PC to use Radio Control Program ARCP-990, ARCP-590G, or ARCP-590 with the USB cable.
This software will not be used while USB Audio function of the transceiver is in use in KENWOOD NETWORK COMMAND SYSTEM.
Please refer to the following manuals for details.
TS-990S USB Audio Setting Manual : (337KB PDF).
TS-590SG USB Audio Setting Manual : (207KB PDF).
TS-590S USB Audio Setting Manual : (366KB PDF).
 
Operating Environment
1. Operating System (OS)
Windows Vista® (Service Pack 2 or later)(32-bit)
Windows® 7 (RTM or later) (32-bit or 64-bit)
Windows® 8 (RTM or later) (32-bit or 64-bit)
Windows® 8.1 (RTM or later) (32-bit or 64-bit)
Note:
This software is designed to run on the above operating systems.
Applicable operating systems are subject to change without notice due to the end of the technical support by Microsoft Corporation or change of the product specifications.
2. Processor
Faster than the recommended CPU for each OS.
3. System Memory (RAM)
Larger than the recommended System Memory for each OS.
4. Free Hard Drive Space
100 MB or more of free hard drive space.
5. Runtime
Microsoft .NET Framework 3.5 (includes .NET 2.0 and 3.0).
6. Peripheral Devices
A display with resolutions higher than XGA (1024 x 768).
A keyboard and a mouse, or other pointing devices.
USB 2.0 interface.
* If the transceiver is connected to a PC using a USB cable, ensure that the connection is directly in place. ARUA-10 may not behave properly if a connection is in place through a USB hub..
* Download and install the virtual COM port driver to make a USB connection possible for command communications via a USB connector.
Sound function.
A speaker.
A microphone.
 
Usage Notes
 
If you are remotely controlling the Transceiver using this software via a network such as the Internet, you must conform to the radio laws and relevant domestic laws of the country and/or area where the Transceiver and relevant equipment are installed.
If any problem occurs while you are remotely controlling the Transceiver and relevant equipment, the responsibility of finding a solution to the problem is left solely to the user who remotely controls the Transceiver and relevant equipment.
Users are required to obtain an approval from JVC KENWOOD, in writing, prior to redistributing this software on a personal web page or packet radio.
Users are prohibited to assign, rent, lease, or resell the software.
Users are prohibited to revise, change, translate, merge, de-compile, or reverse engineer the software.
JVC KENWOOD does not warrant that quality and functions of this software comply with each user's purpose of use of this software, and unless specifically described in this document, JVC KENWOOD shall be free from any responsibilities to any defects and indemnities to any damages or losses. Selection and installation of this software shall be made by the User's designation. The User shall take full responsibilities for the use and effects of this Software.
JVC KENWOOD Corporation shall be free from any responsibilities for any incidental losses or damages, such as missing communications or a calling opportunity caused by a failure or performance error of this Software.
JVC KENWOOD shall own all copyrights and other intellectual properties for the software and all manuals and documents attached to the software. The user shall be allowed to use, not to resell, the software by obtaining a license from JVC KENWOOD. While the media in which the software is stored is possessed by the user, the ownership for the software itself shall be reserved for JVC KENWOOD.
 
Installing the ARUA-10
  Extract the downloaded file "ARUA10_300.zip" into a designated folder.
In the designated folder, a folder labeled "ARUA10_300" will be created.
Execute the "Setup.exe" in the folder labeled "ARUA10_300", and follow the instructions that appear on the display to install ARUA-10.

Note:
Administrator privileges are required when installing the software.
To update ARUA-10, execute the same procedure as used for installation, and follow the instructions that appear on the display to install the software. The latest update is written and installed over the currently installed program.
 
Uninstalling the ARUA-10
  Select "ARUA-10" in "Uninstall a program" in the Control Panel and follow the instructions that appear on the display to uninstall the software. Or double-click "Setup.exe", and follow the instructions that appear on the display to uninstall the software.
Administrative privileges are required to uninstall ARUA-10.
Always exit ARUA-10 before uninstalling the software..
 
If you agree with the details listed above, click the following link to download the ARUA-10 software.
(The latest version includes all previous updates.)
ARUA-10 Ver.3.00 :ARUA10_300.zip 6.83MB download
 
Update History
  Ver.3.00 (October 31, 2014)
Enables to use with the TS-590SG.
Adds Windows® 8.1 compatibility.
 
  Ver.2.01 (July 12, 2013)
Adds Windows® 8 compatibility.
 
  Ver.2.00 (February 28, 2011)
Enables to use with the TS-990S.
 
  Ver.1.00 (October 15, 2010)
First Release.
 
For inquiries, please access:
 
Windows Vista®, Windows®7, Windows®8, Windows®8.1, and Windows logo are registered trademarks of Microsoft Corporation in the United States and/or other countries.
.NET Framework is a trademark or a registered trademark of Microsoft Corporation in the United States and/or other countries.
 
  Copyright 2013 JVCKENWOOD Corporation