TM-D710GA / TM-D710GE Operation Panel
Firmware update information
Last updated : October 31, 2016
 
The TM-D710GA/GE transceiver's Operation Panel firmware has been updated from Version 1.01 to Version 1.02 as follows.
We are offering the firmware updating program to the TM-D710GA/GE owners.
You can update the firmware by connecting the TM-D710GA/GE Operation Panel to the PC by using an optional Programming Cable (PG-5G, or PG-5H Serial communications cable).
The firmware updating program is not applicable for the TM-D710A/E (RC-D710).
 
Updated item : (Version 1.01 1.02) [October 31, 2016]
  Updates the following feature.
 
 
1. Enables display of the model names "TH-D74", "FT2D", "FTM-100D" when received position packets from the KENWOOD TH-D74A/E, and the Yaesu FT2DR/E, FTM-100DR/E.

Updated item : (Version 1.00 1.01) [January 29, 2015]
  Revises the following symptom.
 
 
1. When using an external GPS receiver, the date might not be set correctly from the GPS satellite information on rare occasions.
Applicable models/units :
The firmware updating program is applicable for following models/units.
Models: TM-D710GA / TM-D710GE
Serial numbers: From S/NO.B3Axxxxx through S/NO.B6Axxxxx approx.
Notes : You can find the serial number imprinted on the TM-D710GA/GE's TX/RX unit (main body) bottom side; it consists of an 8-digit number beginning with "S/NO."
: You can check the firmware version of your TM-D710GA/GE by the following procedures.
 
1. With using the MCP-6A
  Select "Model" and then "Transceiver Information" in the MCP-6A menu after connecting the transceiver with a PC by using the PG-5G or PG-5H PC interface cable.
2. Without using the MCP-6A (TM-D710GA/GE standalone)
  Press [PF1] + Power ON.
The Operation Panel's firmware version appears in the right side of the LCD display.

Operating Environments
1. Operating System (OS)
  Windows Vista® (Service Pack 2 or later)(32-bit or 64-bit)
Windows® 7 (Service Pack 1 or later) (32-bit or 64-bit)
Windows® 8.1 (RTM or later) (32-bit or 64-bit)
Windows® 10 (Version 1511 (Build 10586.0) or later) (32-bit or 64-bit)
  Note:
This software is designed to run on the above operating systems.
Applicable operating systems are subject to change without notice due to the end of the technical support by Microsoft Corporation or change of the product specifications.
2. Processor
  Faster than the recommended CPU for each OS.
3. System Memory (RAM)
  Larger than the recommended System Memory for each OS.
4. Free Hard Drive Space
  Larger than the recommended Free Hard Drive Space for each OS.
5. Runtime
  Microsoft .NET Framework 3.5 (includes .NET 2.0 and 3.0).
6. Peripheral Devices
 
A display with resolutions higher than VGA.(640 x 480)
A keyboard and a mouse, or other pointing devices.
An RS-232C interface.
An optional programming cable.(PG-5G, or PG-5H Serial communications cable)
 
Attention
If you do not want to lose user data, save the data using the Memory Control Program MCP-6A before updating the firmware and write the data back after updating the firmware.
 
Usage Notes
Users are required to obtain a license from JVC KENWOOD Corporation, in writing, prior to redistributing this software on a personal web page or packet radio.
Users may not revise, change, translate, merge, de-compile, or reverse engineer the software.
The quality and performance of the software is not warranted for the applicability of any users. JVC KENWOOD Corporation shall not assume liability for any defects, nor warrant anything other than is expressly provided in the agreement. The selection and introduction of the products as well as the results there from shall be upon the liability of the users.
JVC KENWOOD Corporation shall own all copyrights and other intellectual properties for the software and all manuals and documents attached to the software. The user shall be allowed to use, not to resell, the software by obtaining a license from JVC KENWOOD Corporation. While the media in which the software is stored is possessed by the user, the ownership for the software itself shall be reserved for JVC KENWOOD Corporation.
 
Installation :
1. Extract the downloaded file "TM-D710G_OpPanel_V102E.zip" into a designated folder.
In the designated folder, a folder labeled "TM-D710G_OpPanel_V102E" will be created.
2. In the folder labeled "TM-D710G_OpPanel_V102E", the firmware updating program "TM-D710G_OpPanel_V102_e.exe" and "TM-D710G_OpPanel_e.chm" are automatically created.
 
Updating:
Click to read the firmware updating procedure.
 
Uninstalling :
Delete the folder labeled "TM-D710G_OpPanel_V102E" manually using the Explorer or an alternative method.
If you agree with the details listed above, click the following link to download the firmware updating program.
(The latest version includes all previous updates.)
Latest update: TM-D710G Operation Panel Firmware Update Version 1.02 (October / 2016)
TM-D710G_OpPanel_V102E.zip : 1.20MB download
Windows is a registered trademark or trademark of Microsoft Corporation in the United States and other countries.
Windows Vista is a registered trademark or trademark of Microsoft Corporation in the United States and other countries.
.NET Framework is a registered trademark or trademark of Microsoft Corporation in the United States and other countries.